Manmade TextilesTextile Fibres

Manufacturing of Cuprammonium Rayon Fibres

Introduction

Cuprammonium rayon is a regenerated cellulose fibre produced by dissolving cellulose in a copper-ammonia solution and regenerating it during wet spinning. It is also known as Cupro, Cupra, Cuprama, Cupresa and ammonia silk. Bemberg is a well-known trade name associated with this fibre.

The manufacturing process uses cotton linters as the main raw material. The cellulose is purified, dissolved in an ammoniacal copper solution, filtered and converted into a spinning solution. The solution is then extruded through a spinneret and treated in a coagulation and regeneration bath to form fine cellulose filaments.

1. Raw Materials Used in Cuprammonium Rayon Manufacturing

The main raw material is cotton linters, which provide the cellulose required for fibre production. Rayon pulp may also be used, provided its hemicellulose content is sufficiently low.

The main materials used in the process are:

  • Cotton linters: Source of cellulose.
  • Copper hydroxide or a basic copper salt: Used to prepare the copper-ammonia cellulose solvent system.
  • Ammonia: Helps form the ammoniacal copper solution that dissolves cellulose.
  • Water: Used in solution preparation and fibre coagulation.
  • Dilute sulphuric acid: Used to regenerate cellulose from the copper-cellulose complex.
  • Processing additives: Glycerine, glucose, tartaric acid, citric acid and oxalic acid are listed as possible additions to the spinning solution.

2. Manufacturing Process of Cuprammonium Rayon

The main manufacturing stages are:

  1. Raw material selection
  2. Purification of cotton linters
  3. Preparation of ammoniacal copper solution
  4. Dissolution of cellulose
  5. Filtration and deaeration
  6. Preparation of spinning solution
  7. Wet spinning and cellulose regeneration
  8. Washing and removal of chemicals
  9. Copper recovery
  10. Spin finishing and drying

Flowchart of Cuprammonium Rayon Manufacturing

Cotton Linters
      ↓
Purification
      ↓
Boiling with Caustic Soda and Soda Ash
      ↓
Chlorine Bleaching
      ↓
Washing and Drying
      ↓
Preparation of Ammoniacal Copper Solution
      ↓
Addition of Purified Cellulose
      ↓
Formation of Copper-Cellulose Complex
      ↓
Filtration and Deaeration
      ↓
Preparation of Spinning Solution
      ↓
Extrusion through Spinneret
      ↓
Water Coagulation
      ↓
Cellulose Regeneration in Dilute Sulphuric Acid
      ↓
Washing and Removal of Acid and Salts
      ↓
Copper Recovery
      ↓
Spin Finishing
      ↓
Drying
      ↓
Cuprammonium Rayon Filaments

3. Purification of Cotton Linters

Cotton linters are used as the principal cellulose source. They are purified before dissolution to remove unwanted materials.

The purification steps are:

  1. Boiling: Cotton linters are boiled under pressure with caustic soda and soda ash.
  2. Bleaching: The material is bleached using chlorine.
  3. Washing: The bleached cellulose is washed.
  4. Drying: The purified material is dried before further processing.

Bleached cotton linters are commonly used. Rayon pulp can also be used, but its hemicellulose content should be below 4%.

4. Preparation of Ammoniacal Copper Solution

The solvent system is based on copper-ammonia chemistry. Copper hydroxide or a basic copper salt is mixed with concentrated aqueous ammonia to prepare the ammoniacal copper solution.

The solution is prepared with stirring. The cellulose is then opened up and mixed into this solvent system.

The copper-ammonia solution dissolves cellulose by forming a coordinated cellulose-copper complex. The resulting copper-cellulose solution has a characteristic blue colour.

5. Dissolution of Cellulose

Purified cotton linters are added to the ammoniacal copper solution.

The main operations are:

  1. Prepare the copper-ammonia solution.
  2. Add the opened cellulose material.
  3. Mix until the cellulose dissolves and forms the copper-cellulose complex.
  4. Filter the solution to remove undissolved impurities.
  5. Deaerate the solution to remove entrapped air.

During deaeration, some ammonia is also removed.

The resulting solution is used to prepare the spinning dope.

6. Preparation of Spinning Solution

The filtered copper-cellulose solution is conditioned to obtain a suitable spinning solution.

The spinning solution contains dissolved cellulose in the copper-ammonia system. Its composition varies with the spinning conditions.

The reported composition ranges are:

ComponentConcentration
Cellulose4–11%
Copper4–6%
Ammonia6–10%

A teaching presentation also gives a spinning-solution concentration of approximately 9–10% cellulose. The exact basis of this figure is not specified there.

Glycerine, glucose, tartaric acid, citric acid and oxalic acid are listed as possible additives in the spinning solution.

7. Spinning of Cuprammonium Rayon

Cuprammonium rayon is produced by wet spinning. The spinning solution is extruded through spinneret holes into a liquid medium, where the cellulose-containing solution coagulates and the cellulose is regenerated.

The process is commonly described as a two-bath process.

7.1 First Bath: Coagulation

The spinning solution passes through the spinneret and enters a water bath.

In this first bath, the cellulose-ammonium copper complex is precipitated. This step causes the extruded solution to form filaments.

7.2 Second Bath: Cellulose Regeneration

The filaments then pass into a dilute sulphuric acid bath.

The acid regenerates cellulose from the copper-cellulose complex. The regenerated cellulose forms the cuprammonium rayon filaments.

A reported acid-bath condition is:

  • Sulphuric acid concentration: 1.5–2%
  • Bath temperature: 20–24°C

7.3 Stretch Spinning

The teaching presentation describes the formation of relatively thick threads during spinning. These threads are subsequently stretched to produce very fine filaments.

This stretching operation is referred to as stretch spinning.

8. Washing and Post-Spinning Treatment

After regeneration, the filaments contain residual acid and salts. They must be treated before drying.

The main post-spinning operations include:

  1. Washing: Removes residual acid and salts from the filaments.
  2. Copper removal and recovery: Copper is removed from the fibre-processing system and recovered.
  3. Spin finishing: A suitable finish is applied to the filaments.
  4. Drying: The treated filaments are dried.

The final product is cuprammonium rayon fibre.

9. Properties of Cuprammonium Rayon

Cuprammonium rayon has a smooth surface and an almost perfectly round cross-section. It is associated with a silk-like handle and a gentle texture.

9.1 Physical and Mechanical Properties

PropertyReported value or description
Minimum fineness1.33 denier
Dry tenacity1.7–2.3 g/denier
Wet tenacity0.9–2.3 g/denier
Elongation at break10–17%
DensityLess than 1.54 g/cm³
Moisture content11%
Cross-sectionAlmost perfectly round
SurfaceSmooth
HandleSilk-like and gentle

9.2 Moisture Behaviour

Cuprammonium rayon absorbs and releases moisture. The teaching material describes moisture movement through very small waterways within the fibre structure.

This moisture behaviour is associated with a cool and comfortable feeling during wear.

9.3 Thermal Behaviour

The teaching presentation reports that the fibre burns rapidly and chars at approximately 180°C. It also states that ash containing copper remains after ignition.

A melting-point figure of 250 is listed in the presentation, but its unit and measurement context are not given. It is therefore not included as a confirmed melting-point value.

9.4 Chemical Properties

The fibre is reported to:

  • Degrade in strong alkalis.
  • Degrade in acids.
  • Be damaged by undiluted bleaches.
  • Resist dry-cleaning solvents.

9.5 Effect of Sunlight

Cuprammonium rayon contains a high amorphous region. The presentation reports that exposure to sunlight in the presence of oxygen and moisture degrades and weakens the fibre.

10. Dyeing Characteristics

Cuprammonium rayon can be dyed with direct dyes. The teaching material also notes that deeper shades can be obtained.

11. Applications of Cuprammonium Rayon

Cuprammonium rayon is used in textile products where a fine, smooth and silk-like handle is required.

The applications listed include:

  • Fine garments
  • Linings
  • Home textiles
  • Active wear
  • Shawls
  • Lingerie
  • Blouses
  • Summer dresses
  • Other light and form-fitting clothing

12. Advantages and Limitations

Advantages

  • Produces fine filaments.
  • Has an almost round cross-section and smooth surface.
  • Provides a silk-like handle.
  • Absorbs and releases moisture.
  • Can be used for fine garments and lightweight clothing.
  • The cuprammonium process is described as producing fewer harmful secondary substances than the viscose process.

Limitations

  • The fibre is weakened by sunlight exposure in the presence of oxygen and moisture.
  • Strong alkalis and acids can degrade the fibre.
  • Undiluted bleaches can damage it.
  • Copper-containing processing chemicals require removal and recovery after spinning.

13. Difference Between Cuprammonium Rayon and Viscose Rayon

Both cuprammonium rayon and viscose rayon are regenerated cellulose fibres. However, their cellulose dissolution systems and manufacturing routes are different.

FeatureCuprammonium RayonViscose Rayon
Cellulose solvent systemCopper-ammonia systemCellulose xanthate dissolved in dilute caustic soda
Main raw material noted hereCotton linters; rayon pulp may also be usedNot detailed in the cuprammonium process description
DissolutionCellulose forms a copper-cellulose complexCellulose is converted into cellulose xanthate
Fibre formationWet spinning and cellulose regenerationWet spinning and cellulose regeneration
Characteristic notedFine filaments and silk-like handleNot compared in detail here

14. Frequently Asked Questions

1. What is cuprammonium rayon?

Cuprammonium rayon is a regenerated cellulose fibre made by dissolving cellulose in an ammoniacal copper solution and regenerating it during wet spinning.

2. What is the raw material used for cuprammonium rayon?

Cotton linters are the usual raw material. Rayon pulp may also be used when its hemicellulose content is below 4%.

3. Which solvent is used in cuprammonium rayon manufacturing?

An ammoniacal copper solution, prepared using copper hydroxide or a basic copper salt and concentrated aqueous ammonia, is used to dissolve cellulose.

4. Why does the copper-cellulose solution appear blue?

The dissolution of cellulose in the copper-ammonia solvent system forms a blue copper-cellulose complex.

5. Which spinning method is used for cuprammonium rayon?

Cuprammonium rayon is produced by wet spinning.

6. Why is sulphuric acid used during spinning?

Dilute sulphuric acid is used to regenerate cellulose from the copper-cellulose complex.

7. What is stretch spinning?

Stretch spinning is the stretching of the relatively thick threads formed during spinning to produce very fine filaments.

8. What is the cross-sectional shape of cuprammonium rayon?

The fibre has an almost perfectly round cross-section and a smooth surface.

9. Which dyes are used for cuprammonium rayon?

Direct dyes are listed for cuprammonium rayon, and deeper shades can be obtained.

10. What are the main applications of cuprammonium rayon?

Its listed applications include fine garments, linings, home textiles, active wear, shawls, lingerie, blouses and summer dresses.

Infographics

Flowchart showing cuprammonium rayon manufacturing from cotton linters through purification, copper-ammonia cellulose dissolution, filtration, deaeration, two-bath wet spinning, cellulose regeneration and post-spinning treatment.

Discover more from Online Textile Academy

Subscribe to get the latest posts sent to your email.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
error: Content is protected !!

Adblock Detected

Please consider supporting us by disabling your ad blocker